fping
Sends ICMP ECHO_REQUEST packets to network hosts
Site oficial:
https://www.fping.org/
Empacotamento:
https://salsa.debian.org/debian/fping
Versão no Kali: 5.1-1 · Arquiteturas: any · Comandos: 2
Metapacotes:
kali-linux-default
kali-linux-everything
kali-linux-headless
kali-linux-large
kali-tools-information-gathering
Documentação do Kali:
https://www.kali.org/tools/fping/
fping is a ping like program which uses the Internet Control Message Protocol (ICMP) echo request to determine if a target host is responding. fping differs from ping in that you can specify any number of targets on the command line, or specify a file containing the lists of targets to ping. Instead of sending to one target until it times out or replies, fping will send out a ping packet and move on to the next target in a round-robin fashion.
sudo apt install fping (93 KB)
Dependências: libc6, libcap2-bin, netbase
Escolha um comando ao lado para ver a descrição e a ajuda completa.
fping
Send ICMP ECHO_REQUEST packets to network hosts
root@kali:~# fping -h
Usage: fping [options] [targets...]
Probing options:
-4, --ipv4 only ping IPv4 addresses
-6, --ipv6 only ping IPv6 addresses
-b, --size=BYTES amount of ping data to send, in bytes (default: 56)
-B, --backoff=N set exponential backoff factor to N (default: 1.5)
-c, --count=N count mode: send N pings to each target
-f, --file=FILE read list of targets from a file ( - means stdin)
-g, --generate generate target list (only if no -f specified)
(give start and end IP in the target list, or a CIDR address)
(ex. fping -g 192.168.1.0 192.168.1.255 or fping -g 192.168.1.0/24)
-H, --ttl=N set the IP TTL value (Time To Live hops)
-I, --iface=IFACE bind to a particular interface
-l, --loop loop mode: send pings forever
-m, --all use all IPs of provided hostnames (e.g. IPv4 and IPv6), use with -A
-M, --dontfrag set the Don't Fragment flag
-O, --tos=N set the type of service (tos) flag on the ICMP packets
-p, --period=MSEC interval between ping packets to one target (in ms)
(in loop and count modes, default: 1000 ms)
-r, --retry=N number of retries (default: 3)
-R, --random random packet data (to foil link data compression)
-S, --src=IP set source address
-t, --timeout=MSEC individual target initial timeout (default: 500 ms,
except with -l/-c/-C, where it's the -p period up to 2000 ms)
Output options:
-a, --alive show targets that are alive
-A, --addr show targets by address
-C, --vcount=N same as -c, report results in verbose format
-d, --rdns show targets by name (force reverse-DNS lookup)
-D, --timestamp print timestamp before each output line
-e, --elapsed show elapsed time on return packets
-i, --interval=MSEC interval between sending ping packets (default: 10 ms)
-n, --name show targets by name (reverse-DNS lookup for target IPs)
-N, --netdata output compatible for netdata (-l -Q are required)
-o, --outage show the accumulated outage time (lost packets * packet interval)
-q, --quiet quiet (don't show per-target/per-ping results)
-Q, --squiet=SECS same as -q, but add interval summary every SECS seconds
-s, --stats print final stats
-u, --unreach show targets that are unreachable
-v, --version show version
-x, --reachable=N shows if >=N hosts are reachable or not
fping6
Backwards compatibility with fping below version 4.0
root@kali:~# fping6 -h
Usage: fping6 [options] [targets...]
Probing options:
-4, --ipv4 only ping IPv4 addresses
-6, --ipv6 only ping IPv6 addresses
-b, --size=BYTES amount of ping data to send, in bytes (default: 56)
-B, --backoff=N set exponential backoff factor to N (default: 1.5)
-c, --count=N count mode: send N pings to each target
-f, --file=FILE read list of targets from a file ( - means stdin)
-g, --generate generate target list (only if no -f specified)
(give start and end IP in the target list, or a CIDR address)
(ex. fping6 -g 192.168.1.0 192.168.1.255 or fping6 -g 192.168.1.0/24)
-H, --ttl=N set the IP TTL value (Time To Live hops)
-I, --iface=IFACE bind to a particular interface
-l, --loop loop mode: send pings forever
-m, --all use all IPs of provided hostnames (e.g. IPv4 and IPv6), use with -A
-M, --dontfrag set the Don't Fragment flag
-O, --tos=N set the type of service (tos) flag on the ICMP packets
-p, --period=MSEC interval between ping packets to one target (in ms)
(in loop and count modes, default: 1000 ms)
-r, --retry=N number of retries (default: 3)
-R, --random random packet data (to foil link data compression)
-S, --src=IP set source address
-t, --timeout=MSEC individual target initial timeout (default: 500 ms,
except with -l/-c/-C, where it's the -p period up to 2000 ms)
Output options:
-a, --alive show targets that are alive
-A, --addr show targets by address
-C, --vcount=N same as -c, report results in verbose format
-d, --rdns show targets by name (force reverse-DNS lookup)
-D, --timestamp print timestamp before each output line
-e, --elapsed show elapsed time on return packets
-i, --interval=MSEC interval between sending ping packets (default: 10 ms)
-n, --name show targets by name (reverse-DNS lookup for target IPs)
-N, --netdata output compatible for netdata (-l -Q are required)
-o, --outage show the accumulated outage time (lost packets * packet interval)
-q, --quiet quiet (don't show per-target/per-ping results)
-Q, --squiet=SECS same as -q, but add interval summary every SECS seconds
-s, --stats print final stats
-u, --unreach show targets that are unreachable
-v, --version show version
-x, --reachable=N shows if >=N hosts are reachable or not
